• 当前位置:焊接技术首页 >> 焊接资料 >>
  • 焊接专业英语词汇(焊接结构及工装)
  •  2007-07-12 23:30:17  作者:网络  来源:  浏览次数:0  网友评论0
  •  文字大小:【】【】【】 评分等级:0
  • 焊接结构welded structure/ welded construction

    焊件weldment
    焊接部件weld assembly
    组装件built-up member
    接头设计joint design
    焊接应力welding stress
    焊接瞬时应力transient welding stress
    焊接残余应力welding residual stress
    热应力thermal stress
    收缩应力contraction stress
    局部应力local stress
    拘束应力constraint stress
    固有应力inherent stress
    固有应变区inherent strain zone
    残余应力测定residual stress analysis
    逐层切割法Sach’s method
    X射线衍射法X-ray stress analysis
    小孔释放法Mathar method
    固有应变法inherent strain method
    消除应力stress relieving
    局部消除应力local stress relieving
    应力重分布stress redistribution
    退火消除应力stress relieving by annealing
    温差拉伸消除应力low temperature stress relieving
    机械拉伸消除应力mechanical stress relieving
    应力松弛stress relaxation
    焊接变形welding deformation
    焊接残余变形welding residual deformation
    局部变形local deformation
    角变形angular distortion
    自由变形free deformation
    收缩变形contraction deformation
    错边变形mismatching deformation
    挠曲变形deflection deformation
    波浪变形wave-like deformation
    火焰矫正flame straightening
    反变形backward deformation
    焊接力学welding mechanics
    断裂力学fracture mechanics
    弹塑性断裂变形elasto-plastic fracture mechanics
    线弹性断裂力学linear elastic fracture mechanics
    延性断裂ductile fracture
    脆性断裂brittle fracture
    应力腐蚀开裂stress corrosion cracking
    热应变脆化hot straining embrittlement
    临界裂纹尺寸critical crack size
    裂纹扩展速率crack propagation rate
    裂纹张开位移(COD)crack opening displacement
    拘束度restraint intensity
    拘束系数restraint coefficient
    应变速率strain rate
    断裂韧度fracture toughness
    应力强度因子stress intensity factor
    临界应力强度因子critical stress intensity factors
    罗伯逊止裂试验Robertson crack arrest test
    ESSO试验ESSO test
    双重拉伸试验doucle tension test
    韦尔斯宽板拉伸试验Well’s wide plate test
    帕瑞斯公式Paris formula
    断裂分析图fracture analysis diagram
    焊接车间welding shop
    焊接工作间welding booth
    焊接工位welding post/ welding station
    焊工welder
    电焊工manual arc welder
    气焊工gas welder
    焊接检验员weld inspector
    焊工培训welders training
    焊工模拟训练器trainer of synthetic weld
    焊工考试welder qualification test
    焊工合格证welder qualification/ welder qualified certification
    钢板预处理steel plate pretreatment
    喷沙sand blast
    喷丸shot blast
    矫正straighten
    开坡口bevelling (of the edge)/ chanfering
    装配assembly/ fitting
    安装erect
    刚性固定rigid fixing
    装配焊接顺序sequence of fitting and welding
    焊接工艺评定welding procedure qualification
    焊接工艺规程welding procedure specification
    焊接工艺试验welding procedure test
    焊接工艺卡welding procedure card
    工序operational sequence
    焊接材料消耗定额welding consumables quota
    焊接工时定额welder-hour quota
    清渣slag removal
    清根back gouging/ back chipping
    锤击peening
    返修次数number of rewelding
    焊接工作台welding bench
    装焊平台welding platen
    电磁平台electromagnetic platen
    焊接翻转机welding tilter
    焊接变位机positioner
    焊接滚轮架turning rolls
    焊接操作机manpulator
    焊工升降台welder’s lifting platform
    焊接夹具welding jig/ fixture
    磁力夹紧器magnetic jig
    螺旋推撑器screw operated tensioning unit
    焊丝盘绕机welding wire coiler
    焊条压涂机welding electrode extrusion press
    红外线加热器infra-red heater
    干燥箱dryer
    焊条保温筒thermostat for electrode
    流量计flow meter
    CO2预热器CO2 heater
    CO2干燥器CO2 desiccator
    焊接电缆welding cable
    电缆夹头welding connector
    地线earth lead
    地线夹头earth clamp
    焊接参数记录仪welding parameter recorder
    焊缝检测规weld gauge
    喷嘴通针tip cleaner
    测温笔tempil stick
    敲渣锤chipping hammer
    焊接衬垫backing/ welding backing
    保留垫板fusible backing/ permanent backing
    临时垫板temporary backing
    焊剂垫flux backing
    惰性气体衬垫inert-gas backing
    引弧板run-on tab/ end tab/ starting weld tab
    引出板run-off tab/ end tab
    定位板strong-back
    加强勒stiffener
    嵌条insert
    套环ferrule
    面罩helmet
    滤光镜片filter glass/ welding glass
    防护镜片cover glass/ plain glass
    气焊眼镜welding goggles
    焊接机器人welding robot
    点焊机器人spot welding robot
    弧焊机器人arc welding robot
    切割机器人cutting robot
    焊接机器人工作站welding robot station
    机器人运动自由degree of free for robot
    机器人工作空间robot working space
    轨迹重复精度path repeatability
    点位重复精度PTP repeatability
    焊接专家系统welding expert system
    焊接机器人示数welding robot play back
    焊接图象识别pattern recognition for welding
    焊接图象处理welding image processing
    计算机辅助焊接工艺设计computer-aided welding process programming (CAWPP)
    计算机辅助焊接结构设计computer-aided design for welding structure

  • 本文引用地址:http://www.weldinfo.com.cn/skill/html/skill_1947.shtml
  • 责任编辑:网络
  • 发表评论】 【加入收藏】 【告诉好友】 【打印本页】 【关闭窗口】 【返回顶部
  • 发表评论
  • 评分: 1 2 3 4 5

        
  • ·请遵守《互联网电子公告服务管理规定》及中华人民共和国其他各项有关法律法规。
  • ·严禁发表危害国家安全、损害国家利益、破坏民族团结、破坏国家宗教政策、破坏社会稳定、侮辱、诽谤、教唆、淫秽等内容 。
  • ·用户需对自己在使用本站服务过程中的行为承担法律责任(直接或间接导致的)。
  • ·本站管理员有权保留或删除评论内容。